Fiber Optic Sight set for the Taurus G3, G2C, G2S, PT111 G2, PT140 G2, PT709, PT740, and TX22

(3 customer reviews)

$39.99

In stock

Description

Fiber Optic sight set (front and rear) for your Taurus G3, G2C, G2S, PT111 G2, PT140 G2, PT709, PT740, and TX22. The sights come with 3 fiber optic rods in green, red and orange so you can use any combination of color that you prefer.  They are machined from tough aircraft grade Aluminum Alloy and hard anodized and provide outstanding contrast in daylight.

With a flat surface on the front of the rear sight, these sights allow one-handed charging of the pistol action.

They are both held in with screws and no sight pusher is used in the installation.  The tools needed include drivers to remove the existing sights, a small Phillips head screw driver, thread locker, nail clippers or a side cutter, and a lighter to install the fibers into the sights.  Expect miner fitting  of both sights to be required (For example- filing using needle files or similar) because they are made to the largest dovetail size so a tight fit can be had on any pistol.  Yes, dovetails vary.

The sight set comes with new screws for the front sight and rear sights.  The rear sight is adjustable for windage when mounting.

Front screw – M2.5 X .45 X 2.5            Rear screw – M2.5 X .45 X 4

 

Sold in the Continental U.S., Alaska and Hawaii only.

WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

 

Additional information

Weight 2.0 oz
Dimensions 7 × 1 × 5 in

3 reviews for Fiber Optic Sight set for the Taurus G3, G2C, G2S, PT111 G2, PT140 G2, PT709, PT740, and TX22

  1. nmosby1

    I’m very happy with the fiber optic sight set. Very easy to install and a massive improvement over the stock sights that came on my Taurus G2C. Here’s a tip, ***if you have a hard time removing the stock Allen head screw for the original factory front sight and strip it out as I did, take some pliers and just destroy the front sight until it pulls off the screw and the screw will simply fall out. Ready to install the new sight in no time. In fact if I were to install another set of these I wouldn’t even bother to unscrew the stock screw on the front sight, just wiggle back and fourth with pliers and rip it off. Easy to do and didn’t scratch my gun. Throwing that front sight in the trash anyway! The fiber optic rods melt and bead up quickly with very little material exposed, more than just a 1/16 inch and your dot will be larger than the frame of the sight. I intentionally made my front red and a little larger. Went with green for rear sight and stayed a bit smaller on the bead

  2. Jonathan Freeman

    Excellent product and easy installation.
    First time installing any sights on a pistol and had no problems.

  3. eam195 (verified owner)

    Fully agree with a previous review. These sights are a BIG upgrade over the stock sights on my Taurus G2c.
    Had to do a bit of fitting on the front sight in order to get it to set flush with the slide, but overall the installation was easy. A little hint when installing the fiber optic rods. Leave the rod full length with about 1/4″ projecting beyond the angled end of the sight and begin heating the rod while rotating it. Once the end begins to “mushroom” pull the rod lightly into the end of the sight. The rod conforms very nicely to the shape of the sight. Clip off the other end leaving about a 1/16″ and hold the other end of the rod tight to the sight while heating it. The ends come out very nice and consistent.

Add a review